Log Your AI Notify me

How it works · ERG mode

ERG mode, and free riding in it

Marco Bremer

ERG mode is the reason I ride indoors the way I do. It is also the thing most apps hide inside a workout. This page explains what it is, and how I use it without any workout at all.

What ERG mode is

In ERG mode you give the trainer a target in watts. The trainer then changes its resistance, all the time, so that you produce exactly that power. Pedal faster, and it gets lighter. Pedal slower, and it gets heavier. The watts stay the same.

So you don't shift gears, and the "road" has no hills. 200 watts is 200 watts, at 80 rpm or at 95.

A smart trainer has two other modes:

Mode You set The trainer does
ERG A target in watts Holds your power, whatever your cadence
Resistance A level, like a gear Keeps that resistance; pedal harder for more watts
Slope (or simulation) A gradient in percent Feels like that hill; you shift like outside

Virtual worlds and filmed routes use slope mode: the road decides. Structured workouts use ERG mode: the workout decides. What I wanted is the third thing: ERG mode where I decide, by hand.

What you need

  • A smart trainer that can control its resistance. Almost every current one can, over Bluetooth (the standard is called FTMS) or ANT+ FE-C.
  • An app that sends the target. The trainer does not know what you want on its own.

Can you use a smart trainer without an app? You can pedal on it. But you can't set a wattage target without an app or a bike computer that sends it.

Free ride in ERG mode, without a workout

Most apps tie ERG mode to a workout: you pick one, and the workout sets the watts step by step. Riders keep asking for the other way, a free ride with the trainer holding the watts, or the least complicated way to control the wattage from a phone.

This is how I ride nearly every time:

  1. Connect the trainer, start the ride. No workout chosen.
  2. Set a target, say 150 watts, and warm up.
  3. When I feel like it, go up. 225 for ten minutes. Or 350 for two.
  4. When the effort is over, straight back down to base level.

In RawWatts the target changes with four big buttons: −10, −5, +5 and +10. And the watts I held longest in this ride come back as buttons of thier own, so from 350 back to 150 is one tap. Every target I hold becomes a lap, so afterwards the ride looks like the workout it was.

Why the one tap matters: at the end of a hard effort your cadence drops. In ERG mode the trainer answers a lower cadence with more resistance. That makes you slower still, and after a few seconds the pedals nearly stand. Riders call it the spiral of death. The way out is to drop the target quickly. With a tiny ±5 button and sweaty fingers, that is no fun.

How to set watts by hand on a Tacx, Wahoo or Elite trainer

The trainer brand does not matter much. Any app that speaks FTMS can set a target on current Tacx, Wahoo and Elite trainers. The makers' own apps can control the trainer too.

With RawWatts on an iPhone: open the app, connect the trainer over Bluetooth, start the ride and tap the buttons. There is nothing else to set up. If your trainer is not fully supported yet, record a probe and I look into it.

When ERG mode is not working

A few things I would check first. They are the usual ones, with any app:

  • Two apps at once. Over Bluetooth, usually only one app can control the trainer. If the maker's app or another training app is still connected in the background, the second one gets the numbers but can't set the watts. Close the other app.
  • The trainer is in another mode. Some apps have a switch for ERG, resistance and slope. Check which one is on.
  • Cadence too low. Below a certain speed of the flywheel a trainer can't hold a high target. Pedal faster, or lower the target.
  • Changes take a few seconds. A trainer does not jump from 150 to 300 watts in an instant. Give it three to five seconds before you judge it.
  • A power meter in between. If the app reads watts from pedals or a crank and the trainer from itself, the two can disagree by a few percent. That is normal.

Questions

What is ERG mode? ERG mode is a smart trainer mode where you set a target in watts and the trainer adjusts its resistance to hold that power, whatever your cadence or gear.

Can I use ERG mode in a free ride, without building a workout? Yes, if your app lets you set the target by hand. In RawWatts you start a ride without any workout and change the target watts with −10, −5, +5 and +10 buttons while the trainer holds them.

Is ERG mode good for watching a show while riding? Yes. The trainer holds the watts, so you don't need to look at the screen to stay on target. More in Indoor cycling while watching TV.

Which apps have ERG mode? Nearly all training apps for smart trainers do, most of them inside structured workouts. I compared a lot of them in Indoor cycling apps, by kind.

← Log and notes

No-nonsense indoor cycling for iPhone. Coming soon.

Log Support Press Legal notice Terms Privacy Contact
© 2026 blue media labs GmbH · Made in Germany Built by Marco Bremer, maker of the HEROTIME sports stopwatch and the SwimX FINA points calculator